Thursday, August 23, 2007
If it weren't for bad luck....
I arrived home at about 8:30pm from a long day at work to find a good sized box waiting for me in the driveway. Hmmm, cardboard with transmission fliud all over it. I carted it down to the garage and opened it up. After the first flap was opened, it was obvious that swomeone didn't know what the hell they were doing. The transmission was packaged in STYROFOAM and 2 cardboard boxes!!!! Frank (They guy I bought it from) told me that he paid the money and even gave them the hardware to mount it to a wooden frame. At least there is some liability on their part. Needless to say at this point that the transmission was destroyed completely. Thanks you F@#king UPS Store idiots. This is going to set everything back even further. Great!
Well, a week later... The UPS driver came and picked up the destroyed tranny. I was left with a slip of paper with a phone number on it. I called the number the next day at 10:30 in the morning, but I somehow missed the damage clerk. They were probably too busy damaging stuff. SInce I was calling from home, I'll reserve judgement on working hours. I left my number and waited for the return call... and waited....and waited. After 24 hours, I called again. As my good luck would have it, I was connected with the damage clerk. She was as disinterested in helping me as possible. Oh yes, complete with sighs and one word answers to complicated questions. After grilling her about the process, I found out that UPS will happily destroy something they ship and return it to the original shipper, and even refund the original shipper. Apparently getting my money back was "my problem, not theirs". Can you say FEDEX? I will next time.
Luckily, I am dealing with a truly stand up person in California. He is going to get the refund money and see if the transmission can be re-cased or have a super bell housing installed and send it back to me. Wow, there are good people left in the world. He has sworn off of UPS as well. Hey UPS, it's called customer service. Brown can do nothing for me anymore.
After a quick call to Donnie, we are going to find a junkyard TH400 so he can install the crossmember and driveshaft loop and get the car back to me. I'm not about to rush him - it's been 100+ degrees outside and his shop doesn't have AC.
Stay tuned as the saga continues.
Friday, August 17, 2007
Hot Rod Part 4: Christmas in August
I finally acted on my now very detailed list. I had researched every fitting and component of the brake system. Since I was planning on running a brake pedal assembly that was under the floor, I had to buy 2 lb residual pressure valves (for front and rear disc brakes - fyi rear drums need the higher pressure ones). Sorry, I am liable to throw in little facts that I learned on the way. Back to the list.... It was done. Fuel system, check. Electrical system, check. Steering, braking, engine brackets, flywheel, transmission shims and cooler....check. Double check the prices...check. Wake up after adding up the total... check. Man, that was a big number.
Here is the rear back in the car.
Parts started trickling in. It took me 3 or 4 phone calls to Moser Engineering to get all of the measurements and pertinent information that I needed. I already had a 3.50 geared center section all ready to go. It had a brand new spool (this locks the axles together mechanically - it's not really the way to go for a street car, especially on curves or in the rain). You see, when a car goes around a curve, the inner wheel turns slower than the outer. If the axles are mechanically linked, the tire will chirp and screech it's way around the corner. If it's wet and you hit the gas... it's hello other direction. After numerous discussions with the tech people, I was talked into a spool and back out of it. I opted for a nodular center section (better metal than the housing that I had) and 35 spline axles, also with a locker. This is going to be one stout "bulletproof" rear. I do plan on throwing some slicks on this thing and heading out to the dragstrip at some point and I don't want to spray parts down the track.... This was expensive peace of mind.
I also opted for a serpentine belt system for the engine. Here's my thinking.... Every time the 406 hit the rev limiter (at 5800 rpms), it had a nasty habit of pitching the one and only accessory belt. This wasn't obvious until the car overheated, which sucked. Carrying a spare belt helped, but doing a monster burnout and having to pull over to check the belt (or watch the temperature gauge closely) just didn't fit in to my idea of fun. Plus (this is true) I went to the local (and closest auto parts store for 20 miles) O'Reilly store for a new belt. I approached the counter and told the clerk that I needed a V belt that was 45 inches long. Of course his reply was.... you know it... "What vehicle is this in?". Ummmm, I tried again and got the same question repeated back at me. After informing him that it's not going to be on his computer, he said "Try me". Okay, here goes. "It's a 72 model 400 small block with an Edelbrock long water pump in a 1934 Plymouth coupe". Deer in the headlights looking back at me. Finally, he disappeared into the shelving abyss. Later, he came out carrying a serpentine belt. To make matters even worse, it was 6 feet long! After informing him that I needed a V belt, he came back with a double V belt that was for some lawnmower (It was green). This back and forth continued until I finally gave up. This took 15 minutes out of my life, which is a very long time in an auto parts store line. I figure that I'll find out what Honda takes the same size serpentine belt and save my self some trouble in the future. I am sure the service would have been better if I was asking what neon kit would fit my Hyundai or what chrome coffee can exhaust tip I could put on my Mustang.
My rear end parts came in and instantly I went into a panic. The axles looked WAY too long. I am a newbie to Ford 9" rear ends, and I had just learned that the axles were different lengths (That was call #3 to Moser - figuring out what my pinion offset was). Since the measurements they had me take were only 3/4" different, I expected the axles to be 3/4" different. They weren't. They were like 8" different. I was all set to send them back when I decided to go ahead and mock up an axle and see how it was going to fit. Frustration again - it didn't even go all the way in. Th bearing that was pressed on to it was exactly the same size as the housing end. After a little honing (careful measuring found that the housing end was a little egg shaped) the axle went right in. The same with the other side. After I got them in, I noticed that they were practically touching. In my mind, this verified that they were too long. I even remeasured the whole rear end housing to make sure I had given the original measurements to them correctly. Yup, still 49".
I took a look at the center section and I could now plainly see that this was how the axles were supposed to be. Man, am I ever glad I didn't make that call back to Moser. I try to limit my exposure to the world as a dumbass, and every time it's avoided, it's a small victory for me.
I pulled the intake manifold off (It was in need of some cleaning). To do this, the distributor has to come out. When I pulled it out and laid it on the workbench, it started hemorrhaging oil from the distributor cap. Not good. No HEI for the ol' rod. As luck has it, I happen to have a Joe Hunt magneto. A little more nostalgic.... and buzzing the hell out of radios at stoplights only adds to the effect I am going for. I hope it causes check engine lights to go off in every car within a mile when I fire it up.... I have to send it out for a checkup and have an advance mechanism installed (it's locked out for the previous blower motor). Anyway, the intake was in very poor condition, so I sandblasted it. At some point the battery in the previous owner's car exploded, or something equally corrosive sat on the front half of it for a year. The first clue that I needed to take a closer look at the engine was the fact that the chrome 1 wire alternator on it was flaking chrome off of it like a bad dandruff commercial. Now I had looked the engine over, but I was more concerned with cam lobes and rod bearings, so the cosmetic stuff barely got a glance. It'll work for now, but a tunnel ran or blower are in the future for this engine anyway.
Here's the engine after I cleaned it up and painted it:
Sunday, August 5, 2007
Hot Rod Part 3: Destroying a perfectly good 1934 Coupe
If you have been reading the previous stuff, you have probably come to the conclusion that this car might need a thing or two repaired. Shimmying and shaking at highway speeds isn't the desired way to get down the road. I have done some medium level car work in the past. I have removed and installed engines and transmissions, rear ends, suspension components, etc. I can rebuild a carburetor or an engine. I have put together some medium powered stuff (Less than 500 horsepower) and haven't had any catastrophic failures (Yet...). I've never attempted to rebuild an automatic transmission . My welding is... well, it's crap. It's fine to stick together the wine bottle holder (because if it breaks, it doesn't make much difference to me because I am not much of a wine person). Now if it's a critical component on a chassis, well that's a much different story.
I realized that my chassis needed work. Lots of work - probably expensive. Okay, not probably - definitely. I have looked at the chassis prices in the catalogs.... $7000, $11,000, $14,000.... Name your price. Of course if you happen to be a skilled welder and have the know-how.. you can put one together much cheaper. Well, I barely trust my welding skills on wine that I could care less about. When the welding is in a (hopefully) 700 horsepower going down a track/road at well over a hundred miles an hour... I want to know that somebody that knew what they were doing was at the helm when the weld happened. Since I don't know any welders, the car pretty much sat. I overhorsepowered the car and didn't know what to do.
Now this is a predicament that can't be one that I am alone in. There are too many marginal cars out there that people buy and count on to be right that turn out to be "needy". Most guys I know see the car they are about to purchase for it's potential. I think women (thankfully) work this way on guys... "He's a fixer upper". I have been on the receiving end of many deals that ended up being shitty. It's buyer beware out there and it only takes one engine coming apart on you to tell you that you need to learn more. Now before I go off on a tangent here, most off the people out there selling stuff are honest people who will tell you exactly what they are trying to sell. And then there are the 10% of people who will dog the shit out of a motor/car/car part, fix it so it will run for 10 more minutes, and lie their asses off to get rid of it. Even the most scrutinizing inspections will sometimes come up short. I like to think that these people will "get theirs" someday, hopefully on a piece of medical equipment that keeps them from feeling pain. Sure buddy, a little old lady had it - barely used it. If you haven't been screwed buying used parts, then you are either extremely lucky or you haven't been doing this long. I don't care what your financial situation is, most hot rodders at some time or another end up buying something used.
I have this bad habit of keeping track of what's for sale on the internet. There is a deal that occaisionally pops up that doesn't last long and I like to be one of the first ones to see it. It sucks to find that object of desire that is priced right and miss owning it by a day or even minutes. It's more of a habit than anything else, plus it really gives me an idea of what stuff is selling for. I was bowsing through the ads one day and I ran across this sweet ride.... a 1934 Chevy Coupe. It was almost everything my car wasn't... blown big block, yellow paint, and it was reasonably priced. I started doing some addition in my mind... I couldn't possibly build this car for what it was being sold for.
Now, let me tell you what little knowledge I have about buying cars like this. There is always a reason the car is being sold. You have to be a good judge of character to really figure out what is going on with the deal. Not all cars are being sold so the proceeds can help cure cancer. If you get into this stuff, it's a good idea to be able to identify the people who are really selling their unfinished project because they have a kid going into college from the person who got a killer deal at some auction and are waiting for a sucker to come along and unload it on. A little investigation goes a long way. We are all looking for that person who is selling the car for less than it's really worth, but there are 10 people who are counting on that frame of mind to unload a piece of junk on. Plus, getting over the initial excitement and looking at everything as it is presented to you in a balanced way will save you from certain emotional and financial pain. Most people don't lie, they just don't tell you all of the facts. Knowing what questions to ask can be helpful at uncovering the covered information. For example, when I called about the car, I was told that it used to be the fastest 1934 Chevrolet coupe in the world. Wow, quite a pedigree. This was pretty effective is helping me rationalize what looked like shitty welding underneath the car (or at least some homemade ladder bars). Surely the car had to pass a technical inspection at a track before it was raced which means that it's a good start for a stout street car. Secondly I was told that a famous company made it's mold for their 1934 fiberglass cars off of this very car. This was a good way to convince me that the body was as good as it looked in the pictures. So far, I was actually liking what I heard. Now to ask about the engine. I got the "I don't know anything about the engine - I didn't build it" answer. On a car like this, the engine is the showpiece. It's probably worth as much as the car itself. To build an engine like this correctly would cost at least $10,000. A junk yard special could be put together for as little as $4000 or less. I didn't want to drive across the country and find out that this was the latter. Any person who owns a car like this will always be able to tell you details about the engine. Always. Even if they aren't experts, they can at least tell you basics or refer you to the shop of person that put it together. But to claim to know nothing about it is the same as saying that it is a junkyard piece of shit. This kind of person is hoping that you wil be blinded by the rest of the car, which was not worth the price if the engine turned out to be junk. The last clue came in one of the pictures. There was antifreeze on the pavement under the car in one of the pictures. This told me that the car either overheated in the short time it ran while pulling out of the garage, or it simply had a leak - not a good sign of faith, especially if you are about to spend so much money you won't have much left over to do any major repairs. I looked at what I had already and started to compare buying the Chevy and fixing up the Plymouth. To do either... some cash had to come into my life, which means that something had to go. The something in this case would be my motorcycle - which had been sitting most of the time since we moved to the Atlanta area. I put the ol' for sale sign on it and listed it on the internet too.
I thought that it would be easy to sell a motorcycle that cost me $20,000 and was only 2 years old with 3800 miles on it for $12,000. This bike was perfect, but it had one problem - it was a Victory brand motorcycle. "The new American Motorcycle". Yup, the one that loses 50% of it's value in 2 years or less. What a HUGE mistake that motorcycle was. I wrote more about it in the other article...
I think my price was a little too low. It seemed to scare more people away because they couldn't figure out why such a great bike was so cheap. (I originally tried to get what it was valued at ($15,000) with no luck at all). Finally a person stopped by and took the bike for a quick test ride and realized that I wasn't trying to rip anyone off. He wanted the bike. A week after we finalized the price, he called and let me know that there was a problem with his fianances... you know the rest. But wait, you don't. It so happens that this guy builds cars for a living. Old cars. Fast cars. How fast? Try 3500 horsepower 200+ mile an hour in the quarter mile fast. Yup, nostalgia top fuel funny cars. After more negotiating than a hostile takeover of AT&T, we finally reached a preliminary deal. He was going to fix my chassis and more. He was so reasonably priced that I would pay cash for his work if the deal couldn't get finalized. The car was disassembled and the engine was sold.
There's even a sidenote on the engine sale. This engine cost me $4500 to build. It's an aluminum headed 406 small block Chevy that makes about 450 horsepower and had only the best parts in it. I was selling it for $1500. It sold fast. They guy that bought it called me while I was at work in Macon, Georgia. (I live 100 miles away). We were trying to figure out how to get together to make the transaction when we realized that we were about 5 miles away from each other. After a short drive, a check was written and the next weekend the engine was gone.
The car was completely taken apart. Donnie (the guy who wanted the bike) and I agreed on the work to be done and a cash price in case the bike part of the deal fell through. The car was going to have the frame boxed. Normally, a car frame looks like the letter "C" just elongated. It's pretty strong, but it can still flex under severe loads. Boxing the frame is simply welding more metal on the frame to close the open part of the "C" and make it into more of a "D". This stiffens and strengthens the frame dramatically. The car was also going to have a new Ford 9" housing, Ladder bars, a 6 point roll bar, the body moved back 3" and up 1" (this was to allow a supercharged big block to fit in the chassis, and to give me an extra inch of badly needed headroom. The engine was also gong to be mounted to motor plates instead of motor mounts. This would get rid of any and all homemade crossmembers for good. Here is a picture of the work in progress:
To state the obvious, this car isn't a concourse billet hot rod that has chrome everything on it. I hope it never becomes that, to be honest. The term "Ratrod" gets thrown around a lot nowadays, and I am not building one. People will still call it that and I'll always get the "What color are you going to paint it?" and "When's it going to be finished?" questions because of the flat black paint.
As I was dismantling everything, I was nervous about what I would find. We (we being family members) have purchased cars in the past with all kinds of "engineering", even including body panels being held on by that foam in a can stuff. I really expected to find some horrible surprises under the carpet. This is a 73 year old car after all. As I removed stuff, things started looking bad. Under the carpet was duct tape... under that, foam blocks. This was to help give the appearance of metal that just wasn't there. As it turned out, most of the bad stuff was cut out of the car..... leaving a pretty solid body. What a relief. The only damaged metal was on the inner wheel wells, which are being cut out anyway. Whew!
Here is some of the stuff that came off the frame:
And the body - the firewall and entire floor were going to be cut out. There was even a section of frame welded to the 1/8" thick floor! Talk about weight!
Next the cage was welded in and the body was reunited with the stronger and lighter frame. It started to look like a car again.
The Original deal consisted of a blown 427 Big block to be thrown in with all of the frame work, but I was looking at a lot more money to go into that engine. It was a block and heads with a blower. No ignition or carbs, etc. I was tempted to go with it because the engine was stout and I already had the ignition and a set of 850 douple pumper Holley's that came off of my 69 Chevelle blower motor. But still, it's the little things that get you... starter... Flywheel....it all starts to add up. So I declined on that engine. Donnie found a 454 that was complete and was 99% there. It was naturally aspirated, but it's a start. Plus I needed a cheap powerplant for now, and big blocks aren't the cheapest way to go. In it went.
Here is the car with the engine in it. This is how it came home from the shop. So far, the frame was boxed, new rear housing and ladderbars, roll bar installed, motor plates and engine installed.
Wow, my "to do" list is overwhelming: Brake system (even the pedal assembly), Wire the entire car, Find a transmission (The TH700R4 that came out isn't strong enough for the horsepower I plan to make). I had to buy axles and a center section.... rear brakes.... seats...interior.... Oh crap this is a lot of stuff!
Definitely a "To be continued"!
Sunday, July 29, 2007
My Badass Lawnmower
Here's the mower before:
Scroll down......
2 Wheeled Addiction - A brief history of motorcycles and me.....

This is what to do before you put on your new rear tire.....

Here we are, pre-crash. I knew it was bad luck to take a picture before we went!

Sunday, July 22, 2007
Hot Rod Part 2
Okay, I left you hanging with the story of getting the car back to Tennessee. So now I have this car... It gets registered... titled....insured and driven around.
The engine was a mostly stock small block Chevrolet 350. It was spectactulary stock (It had a slightly larger than stock cam, but the car clearly deserved a meaner idle). Any car that looks like this needs an idle that commands attention. It should make babies instantly cry and inject primal fear into anyone that scares easily. I can't tell you how many times I have "cammed" and engine just so it sounds right. I have learned over the years to approach the engine as a system, but rest assured it's going to have a cam that is on the extreme side of lift and duration that still allows the car to work. Smooth idles flat out suck. This is easy when you have a manual transmission - they are much more forgiving than the automatics when it comes to cam size. Anyway, let's just say that the engine didn't set me on fire. Sure, it was fast, but I needed to be thrilled when I hit the loud pedal..... 300 horsepower wasn't even close to enough. There's another reason for my next step too. There are tons and tons of street rods out there and I would say that a full 90% of them have the same orange Small Block Chevy 350 powering them. Some go for the old school look and try to hide it under a fake set of "Oldsmobile Rocket" valve covers, while others are buried under a mountain of billet aluminum parts. No judgement here (at this time anyway), but a person doesn't get a car like this to blend in. It's such a yawn-fest to see row after row of the same engine wrapped up by different car bodies. These engines are cheap and easy to make power.....
Only one cure for this.... I neede a bigger engine. It just so happens that I used to have a 1969 Chevelle Malibu that I bought in California. It was the real deal as far as muscle cars go.... Plain steel wheels, 4 speed, the interior was unchanged since 1969... as a matter of fact the only changes the car had seen in 30 years was the drivetrain. The engine was a 6-71 blown aluminum headed 454 that came with a dyno sheet of an honest-to-goodness 1000hp. One thousand horspower on tap is a mind blowing amount of horsepower for a stock chassis car to absorb.... especially considering the lack of handling that these things had to begin with. Wow, this is getting long winded, so I'll summarize. Engine didn't live long, rebuilt it, detuned it to a mere 750 HP (pump gas friendly), still too much power for the car, pulled it and built a 406 cubic inch small block, sold the car (with 58,000 original miles on it), traded the small block engine to my brother who traded it to my father... who let it sit for 8 years.
Whew. I need to get some pictures scanned so I can keep this semi-interesting. There are alot more facets to the story.... but this is about the Coupe..... so I digress....
Let's see... needed a bigger engine... oh yes. It just so happens that my Dad had this 406 inch small block sitting around. Now this engine is a very pump gas friendly aluminum headed 450 horsepower engine. In a car like the coupe there are things that just can't be hidden. It's not an engine that can be disguised as a stocker that surprises someone only after the gas pedal is floored. Nope, this thing advertises it's intentions from the very beginning. Aluminum heads, aluminum water pump, single plane high rise intake, Barry Grant emblems on the carburetor, Fluidamper. Once the engine is started, there are no questions about speed.
After a quick and insanely good deal (My Dad doesn't even own a Chevrolet) I put it in the car - it's a direct swap (external dimensions are identical). To the uninitiated it can still pass as a 350... or 305 if they don't know Chevy motors.
Out came the 350 and it was whisked off by a coworker for very little money. Now the fun began...
What started off as a minor project immediately got a nasty start. A little background: When I first looked at the car (back in AZ) I noticed a few things that were not exactly confidence builders. The rear end was suspended by springs that were bolted on the rear housing with generic aftermarket perches. Now, what this means (to the uninitiated) is that someone put a 12 bolt rear (nice strong piece) in the car and got cheap (and maybe unsafe) with how they did it. There were a few things that were questionable.... funky welds, homemade brackets, etc, but hey, this wasn't a race car or even anything close to show quality. Plus this stuff was well hidden and what did show (as far as the frame and suspension) was top notch.
Now for the nastiness..... the car would shake and the frame would pop and emit strange noises when it was pushed semi-hard. After I pulled the engine out, I saw what I thought was the reason. The crossmember that the engine bolted to was not only homemade, but it was cracked completely through. This can't be good. This piece was shabby looking at best (damn I need to figure out this picture thing). It was a rough piecve of metal that was thankfully hidden by the installed engine. Time to buy a welder. This was the excuse I was looking for to get one! I couldn't expect to have a 74 year old car and not have the capabilities to stick metal back together, could I? Luckily one of my coworkers welded for years and years and I conned him into coming over and welding the crossmember back together under the guise of teaching me. His welding (partially mine too) was by far the best looking part of the crossmember).
Now, when I put the new engine in place, there was an immediately noticeable problem. The engine was crooked. Very crooked. If this was a car with a hood and fenders to hide the engine, I may have been tempted to let it go. But with the sidepipe exhaust and open engine compartment... it was painfully obvious that the crossmember we just repaired had probably been broken on purpose to keep the engine level. I was now on my own to remove a motor mount and fabricate a motor mount that would align the engine correctly. The friend that helped me weld inspired me to go on by telling me that any mistake I made welding could be easily undone with a grinder. I kept repeating this to myself and in the end the mount was another visual improvement. To me anyway. I would proudly point it out to anyone looking at the car and get the same glazed over look back. It was just a motor mount after all.
The engine went in with minimal fuss and after a quick head gasket change (after all it had been sitting for 8 years) it was off and running. I think it was the second or third time I took the car out I realized the error of my ways. The car had a 4 speed automatic and the tires were 15.5 inches wide each. If I dared stomp the gas in 1st gear (and I did dare), I was rewarded with one rear tire screaming in protest as it went up in smoke. Shift to second and I get more of the same with limited forward motion. The sound of the engine was intoxicating, either idling or at full chat. It was all fun and games until it got traction. This car was capable of speeds it could never stop from, and keep in mind that it still shook and rattled it's way down the road. It was seriously over powered and I loved it. This is the form it would stay in for the next couple of years. I had heard about making race cars stiffer, and suddenly I understood why. Until you have felt a chassis flex and twist under the loads an engine like this can generate, well, you just haven't lived.
I pushed the car to over 100 mph once. Now before you get ready to tell me that your Grandma's minivan can do that, let me explain a few things. Harley Davidson riders think their bikes are fast. Why is that? Because the sensation of speed is a lot different. Those bikes shudder and thud their way up to speed and the wind noise, engine noise, and riding position generate a sensation that tells the rider that indeed they are going fast. If it's a Harley, chances are they aren't. I used to have a Suzuki Hayabusa. For those of you that know, enough said. This thing was real world capable of a factory limited (thanks Europe!) 186 mph (Which I did hit - and I did know that I was going very, very fast). Anyway, 110 mph was a cruising speed on this bike. 70 mph felt like I could get off of the motorcycle and walk next to it. Different perspectives of speed. Back to the Coupe....
The sensation of speed was insane in the car. It was loud, lots of wind noise and the feeling of stability just wasn't there. This really lent itself to feeling like you are about to break a world speed record at 60 mph... not to mention that 60 came in around 3 or 4 seconds.... Most cars feel comfortable even when you're a little "out of shape" and lost traction or drift, etc. This car was like an on/off switch when it comes to control. Get it slightly out of shape and you stand a good chance of barrel rolling to an ugly ending. At 95 on a straight section of interstate I knew I was a wind gust, tire pop, idiotic lane change away from ugliness, but I had to get to THE TON (100 mph). Mission accomplished, not to be voluntarily repeated.
Obviously, this had to change. It was fun to have that kind of power on tap, but I'd like to live to tell the tale. I was browsing the internet looking at these old cars and I was sent down a path of inevitable change by a car for sale. Another 1934 Coupe (This time a 3 window Chevy). It was yellow and had a supercharged Big block Chevy motor in it. Former "World's Fastest 1934 Chevy Coupe" according to the owner. It was wicked for sure. I was at a crossroads.... do I sell my car and buy this one? It's exactly what I wanted.... This kind of thing can keep a man awake at night. I need some serious chassis work on my coupe, but we're talking thousands and thousands of dollars and more work that I have ever done to a car before. Sure, I have swapped engines, transmissions, rear ends, etc. I've even tackled manual/automatic conversions. Hmmmmmm, what to do? Well, step 1 was to sell my motorcycle. Not only would this buy me time, but the wallet limits the amount of toys we can have at the same time, right? This process started me down an unexped path once again. The best laid plans of hot rodders NEVER work out the way we expect.
More to come... I am going to try and load some pictures....
Hot Rod part 1 - My Dream Car Realized
My heart was pounding. I just got off of the phone with a very nice gentleman in Phoenix who just spent an hour telling me about the details on a 1934 Plymouth coupe Ratrod. I had just made up my mind that I was going to buy this car (after some wrangling at the credit union for a loan). This was my dream car, and it was looking like it was going to happen.
Fast forward a week later, and I have successfully conned my brother into flying out to Phoenix to get this car with me. We planned on taking a week to slowly saunter from Phoenix back to East Tennessee in the newly purchased ride. The owner had offered to drive it out to TN - a vote of confidence in the car's roadworthiness that convinced me it was a worthy purchase. It was going to be one of those trips that would inspire a movie if it went well. I bought us one-way tickets and we were off to Arizona on a Friday night.
It was 90 degrees out at 9:00 pm when we landed. We were met by a nice couple in their newer Caddy and were whisked off to their home. These people were absolutely some of the nicest people that I have had the pleasure of meeting. We looked at his 1965 El Camino and he went around the house and fired up the coupe. It rumbled it's way around the side of the house and I knew that it was going to be mine the instant I saw it. Here is this black primered 1934 5 window coupe - complete with 15 inch wide rubber on the rear, flames shooting down the side, and no hood. It looked mean. We took a brief test ride around the neighborhood (I drove it like an old lady - this was my first experience in a car like this). Gingerly driving is not like me at all. The ergonomics were cramped at best. This thing had been channeled 8 inches (That's where they cut the floor out and lower the body down on to the frame to give it that wicked stance - all at the expense of the comfort of it's inhabitants). After dinner (home cooked, by the way) we headed out to the great adventure of a cross country trip in a genuine Hot Rod.
Let me explain the car a little bit. It looked cool. It roared down the road with sidepipes and open wheels. It had a 10 gallon fuel tank behind the cardboard divider that seperated us from the trunk. The turn signals were 2 toggle switches that were hanging down above the driver's side door. Along with an indian blanket over the seats there were vintage stickers all over the dash. The suicide doors had little manual pins to keep them from flying open and sucking the occupants out into the great beyond. This was ol' skool all the way. I had to adopt the posture of a cocktail shrimp to fit in the thing, resting my elbow on top of my left knee to fit. The gas and brake pedals were seperated by the steering column which meant that I had to learn to drive two footed. This only took a little bit of time to get used to, but there were a couple of incidents that had me panic accelerating instead of braking.
I am 6'2" when I stand up straight, and my brother is pushing 6'5". Both of us are safely in the 200 pounder club, and it took pure choreography for us to get settled in the seats and tangle ourselves into some form of comfort. Ahh, the sacrifices we make to look cool. I just added a picture at the top so you can see how cramped it was - the guy is my brother....
After about 2 miles of interstate driving, I had a flash of dread about everything. The purchase, the decision to drive it across the country, you name it. I guess after the adrenaline dies off, you start to wonder about what put you in your current situation. You see, my current situation was shaking violently down the interstate (and weaving horribly at any attempts at a lane change) at any speeds from 60mph up to 75mph. It felt like the car was going to weave out of control if I turned too fast or hit a bad pot hole. This ride had my undivided driving attention. It was a strain to keep it in one lane. I can only imagine the terror in my brothers head as he experienced this without being in control. If I was nervous, he had to be nearly terrified.
We made it to the closest gas station and started manipulating the rear tire pressure in hopes of stabilizing the car. After 5 stops we settled on 11 psi in each rear tire. This minimized the shaking, but the weaving was here to stay. Onward we went. Our first destination was going to be Albequerque, NM. We had an old high school friend who was going to let us crash for a few hours (the adventure started at 11pm).
Not being from Arizona, and only having driven through the state a couple of times, we seriously underestimated the climate change. As the elevation kept creeping up, the temperature started dropping. It kept dropping and we assesed the current wardrobe situation. It wasn't good. Both of us packed plenty of shorts and tee shirts, but not the first jacket or sweatshirt. When the temperature hit 40 degrees, I was no longer sure if it was the car or me shaking. The Indian blanket was ripped off of the seats and kept the frostbite at bay. At least I didn't have to worry about falling asleep at the wheel. In case you haven't figured it out, the car had no heater and it isn't even remotely airtight. There was a constant breeze - even after cramming the surplus blanket ends between the seats and the doors. This is exactly why you pick a brother to do this kind of thing with you. Even the best of friends would feel the strain on their friendship with all this going on. But brothers can push the envelope just a little further.... thankfully.
We made it to Albequerque and after some conversation, we crashed at our friends house. After waking up, we hit the local shop and had the tires re-balanced in the hopes of a smoother ride. No such luck. I brought my digital camera (side note: When do I get to stop saying digital? Does anyone use film anymore?) We took a few pictures of the landscape and headed out. these would be our only pictures of the entire trip. Luckily the small gas tank kept us stopping about every 100 miles for a refill. It was a chance to stand upright and let my brain relax from the brutal concentration of not barrel rolling this thing down the interstate and keeping an eye on the gauges of a newly purchased heap. I would occasionally nervously let go of the steering wheel to wave back at the many thumbs ups the car was getting.
I forget exactly what part of the country we made it to when my brother got THE CALL. I could tell by the fevered pitch in his voice and the string of cursing that took me back to my Navy days that something was very wrong. Apparently the water main at his house in Atlanta had ruptured. His girlfriend went on to tell him that the utility people wouldn't tell her where the water cutoff valve was located, because she wasn't on the utility bill and they weren't married. You want to talk about feeling helpless. These people put the "F" in utility, that's for sure.
Suddenly the trip becomes a cannonball run to save his homes foundation. We were on a mission. I think it was around Oklahoma... which by the way, is NOT okay. I40 couldn't get in any worse shape. Along with being cramped, the car has no suspension travel to speak of. I think the rear can move 2" and the front straight axle feels solidly linked to the chassis. Every bump and pothole sent us travelling upward in the car only to be stopped by the wooden frame that is the interior roof. A couple of times I found myself looking at my hands for signs of blood as the sting on my scalp slowly faded away. All this while trying to keep this thing in our own lane at 80 mph. At 80, the car's ride smoothed out, plus it was fun buzzing by the beige import sedans and minivans as kids pointed and mothers scowled as we roared by. This car brings out your inner rebel, for sure.
We only had one "moment" the entire trip. You never realize how far it can be in between filling stations until you have to stop every 100 miles. Here we were with 120 on the mileage (which the speedometer would occaisionally go into epileptic fits and bounce from 40-100, so accuracy wasn't a factor) and we needed petrol. I remember it clearly - it was in a construction zone. You know, the kind with lanes closed, orange barrels, but no sign of work. The orange barrels were whizzing by at 80 when I realized that there was an exit, and we were still in the fast lane. The tiny mirrors didn't give me a great deal of rear view, but I saw a gas station sign and had to take my chance. We exited with the front passenger tire locked up and the car leaning hard in protest to the sudden maneuver. My brother applied his imaginary brake pedal and could only sqeak out my name and grip the dash as we barely threaded the makeshift exit ramp between the barrels. To me, it all happened in slow motion, but my heart was still pounding while I pumped the 9 gallons that we needed.
Well, we finally made it back to Tennessee (My brother drove from Memphis to the Knoxville area). Knowing what was involved in driving this beast, I couldn't sleep - even though my body was trying to do just that while driving despite the 105dB constant roar from the engine and wind noise. We made the entire trip in exactly 24 hours. After a good night's sleep at my house in TN, I drove him back down to Atlanta, in my other car, of course.
When I finally got home for good, I enjoyed watching my garage door slowly open and reveal my dream car sitting in it. There it was in all of it's primered, flamed, fat-tired glory. It was the kind of car that you go down to the garage and just stare at, just to make sure it's real. As any gearhead know, this just gets the wheels in your head turning about what to do next. And there is a next, actually, quite a few of them.
Stay tuned......